Mackie Thump TH15A Active Speaker

Options Delivery Price  
Place your order in the next 1 day 23 hours & 55 minutes for delivery in 3 days (Tuesday 31st March 2015)

Designed by the same team that produced the best-selling Mackie SRM450v2, the Mackie Thump TH-15A delivers deep low-end and real power in a lightweight design that is extremely portable. Class-D Fast RecoveryTM amplification pushes 400-watts of power to the high-frequency compression driver and bass-pounding 15? woofer. Plus, Mackie Active processing, including a precision crossover and driver time-alignment provides total optimization for maximum system efficiency. Versatile by design, the TH-15A features a user-adjustable 3-band EQ for tone control and, since it can be pole-mounted or used as a wedge, the TH-15A represents the best value available for a complete stage solution. LF 300W peak power (Class-D) HF 100W peak power (Class A/B)
High-output transducers
15" high-precision woofer
1" compression driver
Mackie Active electronics provide total system optimization
Precision 2-way crossover
Transducer time-alignment
User-adjustable 3-band contour EQ with sweepable mid-frequency
Mic/Line input for direct connection of single microphone
Tough, impact-resistant polypropylene enclosure
Pole-mountable and floor wedge-able
Extremely lightweight and portable (36 lbs)
Acoustic Performance
Frequency Range (-10 dB) : 40 Hz - 20 kHz
Frequency Response (-3 dB) : 50 Hz - 18.5 kHz
Horizontal Coverage Angle : 90 Degrees
Vertical Coverage Angle : 60 Degrees
Maximum SPL Long-Term : 113 dB SPL @ 1m
Maximum SPL Peak : 116dB SPL@1m Input/Output
Input Type : Female XLR Balanced/Unbalanced/li>
Input Impedance : 20k ohms bridging; 10k ohms
Loop-through : Male XLR Balanced/Unbalanced
Level Control : Rotating Knob - 0 dB at center
Sensitivity : +4 dBu for full output (Level control @ center) - -36dBu for full output (Level control @max) Transducers
Low frequency : 15in/381 mm with steel frame paper cone woofer
High Fequency : Horn-loaded 1 in/25 mm exit compression driver Power Amplifiers
Low Frequency Power Amplifier :
Rated Power : 150 watts, 8 ohm load, 300 watts peak
THD : <0.1%
Signal-to-Noise Ratio :> -94 dB, 20 Hz to 20 kHz, unweighted, referenced to 138 watts into 8 ohms
Design: BTL Class D High Frequency Power Amplifier :
Rated Power : 50 watts, 4 ohm load 100 watts peak
THD : <0.1 %
Signal-to-Noise Ratio :> -97 dB, 20 Hz to 20 kHz, unweighted, referenced to 50 watts into 4 ohms
Design:Class AB Electronic Crossover Crossover Type: 24 dB/octave
Crossover Frequency : 3 kHz Equalization
Low Frequency EQ : ±15 dB @ 80 Hz, shelving
Mid Frequency EQ :±15 dB, bandpass, sweepable from100 Hz to 8 kHz
High Frequency EQ :±15 dB @ 12 kHz, shelvingDirect/EQ Switch :Bypasses EQ section Protection Features
Over-excursion Protection : second-order sub-sonic filter
Thermal Protection : Independent amplifier shutdown, auto reset
Driver Protection : Independent HF and LF compressors AC Power Requirements
Europe : 240 VAC, 50 Hz
AC Connector: 3-pin IEC 250 VAC, 20 A male
Fuse : 230 VAC: T 3.15 AL/250 V
Power Consumption : 320 watts with music, loud mix - 20 watts quiescent (idle) Construction Features
Basic Design : Asymmetrical Trapezoidal
Material: Polypropylene
Finish : Textured
Handles : One on each side, one on top
Grille : Perforated metal with weather-resistant coating Display LEDs
Front : Power ON
Rear : Power ON, OL (overload) Physical Dimensions and Weight
Dimensions :
Height : 27.1 in/689 mm
Width : 16.8 in/427 mm
Depth : 15.8 in/401 mm
Weight : 36 lb/16.3 kg Mounting Methods : Pole-mountable via the built-in socket on the bottom of the cabinet. Be sure the pole is capable of supporting the weight of the TH-15A. $stag=free_stands_bag$

Navigation